Definition of titration
The reagent added from burrete to estimate is called as a titrant. The substance underestimation is called titrand.
There are mainly four type of titration defines as bellows
- Acid-base titrations
- Redox titrations
- Precipitation titrations
- Complexometric titrations
The different types of titration are
A) Based on the method of titration:
They are of three types of titration based on the method used in the process of titration.
1. Direct titration
As the name indicates, it is a basic titration. A known amount of titrant is added from a burrete to a titrand sample taken in a flask. Here one substance is analyzed for its quantity by another substance of known volume and concentration.
2. In-direct titration
Theoretically, it is converting a substance into acid and analyzing it with a base. (also vice-versa). This is a method extrapolated to use titration for non readily reactive substances. A substance can be weakly acidic and so it does not permit a precise analysis by direct titration. So first that substance is chemically altered to be more reactive in acidic or basic form and then analyzed by adding a titrant.
3. Back titration
This method is also suitable for weakly reactive or non-reactive substance estimation. Here a substance is allowed to react with excess and known quantity of a base or an acid. The remnant excess base or acid is estimated by a known quantity of acid or base receptively. It is called back titration as we are estimating a substance which was added by us.
B) Based on the nature of solvents and chemical reaction:
The titrations can also be classified based on the nature of solvents used.
Based on the solvent used they can be classified as aqueous and non-aqueous types. Further based on the nature of chemical reaction they are classified as below
Acid-base titrations. ( neutralization):
An unknown sample of acid is estimated with a known quantity base or vice-versa. The result reaches a neutral point at pH-7 and in most cases, salt is formed.
Check out Types of acid-base titration for more.
The full name is oxidation-reduction titration. Here a reducing agent is allowed to react with an oxidizing agent till endpoint. The common oxidizing agents used are Potassium permanganate, bromine, cerium, etc.
As the name indicates, the endpoint is seen by the formation of a complex molecule. Here titrant and titrand react to form a complex till endpoint is reached. Once complex is formed, the complex is stable and no further reaction takes place. The reaction depends on the chelating agent’s ability to form a complex with the sample under test. An example of the chelate is ethylene tetra-acetic acid (EDTA)sodium salt.
The reaction occurs by the formation of a solid precipitate at the bottom of the flask. Here titrant reacts with titrand to form an insoluble precipitate. An example of such a reaction is Silver nitrate with Ammonium chloride. The reaction forms a white precipitate of silver chloride.
2. Non-Aqueous titrations
These are the titration done for organic and medicinal compounds. So widely used in medicinal chemistry and pharmaceutical labs.
a) Acid-base titrations. (neutralization):
Here the reaction occur in organic solvents like glacial acetic acid and the acid used is perchloric acid (HClO4)
b) Redox titrations.
Here the reaction is done as iodometry or iodimetry. Iodine is used as an oxidizing agent and a reducing agent is thiosulfate.
Here the sample made to release iodine from within and this released iodine is measure with sodium thiosulfate as a reducing agent.
Here the sample under test is measured with a known concentration of Iodine.
These are similar to aqueous titrations, but here instead of water as a solvent, an organic solvent is used.
C) Based on the strength of reagents used:
The chemical reaction involved in titration is the main principle of titration. But the chemical reactions also depend on the nature and strength of the reagents used in the reaction.
So acid-base titrations or the neutralization reactions are also further divided as
- Strong acid v/s Strong Base: Here both acid and base are strong. Ex: HCl v/s NaOH. Here the endpoint would be at an exact pH of 7. The salt formed in reaction would be neutral.
- Strong acid v/s Weak Base: A strong acid reacts with a weak base. Ex: HCL v/s NH4OH. Here the endpoint would go towards acidic pH, i.e., below 7. The salt formed in the end would be slightly acidic.
- Weak acid v/s Strong Base: A weak acid reacts with a strong base. Ex: Acetic acid v/s NaOH. Here the endpoint would be tilting towards basic pH, i.e., above 7. The salt formed during neutralization would be slightly alkaline.
- Weak acid v/s Weak Base: Reaction between a weak acid and a weak base. Ex: Acetic acid v/s NH4OH. The endpoint would have a pH of 7. Here the salt formed as a final product would be neutral.
A titrand is taken in a beaker while the titrant is dropped from a burette. The sole purpose of titration is for qualitative and quantitative estimation of a given substance.
These methods are comparatively economic and easy to perform. Further, the technique is also reproducible across all the labs. Hence, they are routinely used in industry, research, and also education.
Calculation: All the processes of titration are noted in a chemistry lab report manually. This includes the molar concentration of solutions, their volumes, indicators, formulas, etc. This helps to calculate final values.